info@bitchipsemiconductors.com

+91-93217 43505

Facebook
Instagram
You-Tube

MICROCHIP

TRADERS SUPPLIERS & STOCKIST

MCP6004T-I/SL MCP

  • Gain Bandwidth Product (GBWP): 1 MHz
  • Quiescent Current: 100 µA (typ.)
  • Supply Voltage Range: 1.8V to 6V
  • Rail-to-Rail Input and Output
  • Extended Temperature Range
  • Space Saving Package Offering: 14-lead PDIP, SOIC, and TSSOP

PIC18F67K22-I/PT MCP

  • nanoWatt XLP Technology for Low Sleep, RTCC, LCD, and WDT Currents
  • Low-Power Brown-Out Reset (BOR)
  • Ultra Low-Power Wake-Up
  • Fast Wake-Up
  • Low Input Leakage Currents
  • Up to 16 MIPS Performance
  • Operating Speed up to 64 MHz
  • Operating Voltage Range: 1.8V to 5.5V
  • 8 x 8 Single-Cycle Hardware Multiplier
  • Three Internal Oscillators: 31 kHz, 500 kHz, 16 MHz
  • Charge Time Measurement Unit for mTouch Sensing
  • A/D Converter: 12-bit Resolution, 16 Channels
  • Ten CCP/ECCP Modules
  • Eleven 8/16-bit Timer/Counter Modules
  • Three Analog Comparators
  • Hardware Real-Time Clock and Calendar (RTCC)
  • Two Master Synchronous Serial Port Modules

PIC18F46K22-I/PT MCP

  • C Compiler Optimized Architecture / Instruction Set
  • Data EEPROM up to 1024 Bytes
  • Linear Program Memory Addressing up to 64 KBytes
  • Linear Data Memory Addressing up to 4 KBytes
  • Up to 16 MIPS Operation
  • 16-bit Wide Instructions with 8-bit Data Path
  • Interrupt Priority Levels Supported
  • 31-Level Software Accessible Hardware Stack
  • 8 x 8 Single-Cycle Hardware Multiplier
  • Sleep Mode Current: 100 nA (Typical)
  • Watchdog Timer Current: 500 nA (Typical)
  • Timer1 Oscillator: 500 nA @ 32 kHz (Typical)
  • Flexible Oscillator Structure
  • Factory Calibrated to ±1%
  • Software Selectable Frequency Range: 31 kHz to 16 MHz
  • 64 MHz Performance Available Using PLL
  • No External Components Required
  • Four Crystal Modes up to 64 MHz
  • Two External Clock Modes up to 64 MHz

PIC18F4620-I/P MCP

  • Up to 10 MIPS Performance at 3V
  • C Compiler Optimized RISC Architecture
  • 8 x 8 Single-Cycle Hardware Multiplier
  • Internal Oscillator Support: 31 kHz to 8 MHz with 4x PLL
  • Fail-Safe Clock Monitor (Safe Shutdown on Clock Failure)
  • Watchdog Timer with Separate RC Oscillator
  • Wide Operating Voltage Range: 2.0V to 5.5V
  • Integrated LCD Driver: 48 Segments, 4 Commons (132 Pixels)
  • Run, Idle, and Sleep Modes
  • Idle Mode Current: 5.8 µA (Typical)
  • Sleep Mode Current: 0.1 µA (Typical)
  • 10-bit ADC with 12 Channels (100K Samples/Second)
  • Programmable Low Voltage Detection Module
  • Programmable Brown-Out Reset Module
  • Two Analog Comparators

PIC18F45K22-I/PT MCP

  • C Compiler Optimized Architecture / Instruction Set
  • Data EEPROM up to 1024 Bytes
  • Linear Program Memory Addressing up to 64 KBytes
  • Linear Data Memory Addressing up to 4 KBytes
  • Up to 16 MIPS Operation
  • 16-bit Wide Instructions with 8-bit Data Path
  • Interrupt Priority Levels Supported
  • 31-Level Software Accessible Hardware Stack
  • 8 x 8 Single-Cycle Hardware Multiplier
  • Sleep Mode Current: 100 nA (Typical)
  • Watchdog Timer Current: 500 nA (Typical)
  • Timer1 Oscillator: 500 nA @ 32 kHz (Typical)
  • Flexible Oscillator Structure
  • Factory Calibrated to ±1%
  • Software Selectable Frequency Range: 31 kHz to 16 MHz
  • 64 MHz Performance Available Using PLL
  • No External Components Required
  • Four Crystal Modes up to 64 MHz
  • Two External Clock Modes up to 64 MHz
  • 4x Phase Lock Loop (PLL)

PIC18F4520-I/P MCP

  • Up to 10 MIPS Performance at 3V
  • C Compiler Optimized RISC Architecture
  • 8 x 8 Single-Cycle Hardware Multiplier
  • Internal Oscillator Support: 31 kHz to 8 MHz with 4x PLL
  • Fail-Safe Clock Monitor (Safe Shutdown on Clock Failure)
  • Watchdog Timer with Separate RC Oscillator
  • Wide Operating Voltage Range: 2.0V to 5.5V
  • Run, Idle, and Sleep Modes
  • Idle Mode Current: 5.8 µA (Typical)
  • Sleep Mode Current: 0.1 µA (Typical)
  • 10-bit ADC with 13 Channels (100K Samples/Second)
  • Programmable Low Voltage Detection Module
  • Programmable Brown-Out Reset Module
  • Two Analog Comparators with Multiplexing

PIC16F887-I/P MCP

  • This powerful yet easy-to-program (only 35 single word instructions) CMOS FLASH-based 8-bit microcontroller packs Microchip's powerful PIC® architecture into an 40- or 44-pin package.The PIC16F887 features 256 bytes of EEPROM data memory, self programming, an ICD, 2 Comparators, 14 channels of 10-bit Analog-to-Digital (A/D) converter, 1 capture/compare/PWM and 1 Enhanced capture/compare/PWM functions, a synchronous serial port that can be configured as either 3-wire Serial Peripheral Interface (SPI™) or the 2-wire Inter-Integrated Circuit (I²C™) bus and an Enhanced Universal Asynchronous Receiver Transmitter (EUSART). All of these features make it ideal for more advanced level A/D applications in automotive, industrial, appliances or consumer applications.

PIC16F886-I/SO MCP

  • This powerful yet easy-to-program (only 35 single word instructions) CMOS FLASH-based 8-bit microcontroller packs Microchip's powerful PIC® architecture into a 28 pin package.The PIC16F886 features 256 bytes of EEPROM data memory, self programming, an ICD, 2 Comparators, 11 channels of 10-bit Analog-to-Digital (A/D) converter, 1 capture/compare/PWM and 1 Enhanced capture/compare/PWM functions, a synchronous serial port that can be configured as either 3-wire Serial Peripheral Interface (SPI™) or the 2-wire Inter-Integrated Circuit (I²C™) bus and an Enhanced Universal Asynchronous Receiver Transmitter (EUSART). All of these features make it ideal for more advanced level A/D applications in automotive, industrial, appliances or consumer applications.

PIC16F883-I/SP MCP

  • This powerful yet easy-to-program (only 35 single word instructions) CMOS FLASH-based 8-bit microcontroller packs Microchip's powerful PIC® architecture into a 28 pin package.The PIC16F883 features 256 bytes of EEPROM data memory, self programming, an ICD, 2 Comparators, 11 channels of 10-bit Analog-to-Digital (A/D) converter, 1 capture/compare/PWM and 1 Enhanced capture/compare/PWM functions, a synchronous serial port that can be configured as either 3-wire Serial Peripheral Interface (SPI™) or the 2-wire Inter-Integrated Circuit (I²C™) bus and an Enhanced Universal Asynchronous Receiver Transmitter (EUSART). All of these features make it ideal for more advanced level A/D applications in automotive, industrial, appliances or consumer applications.

PIC16F877A-I/P MCP

  • This powerful (200 nanosecond instruction execution) yet easy-to-program (only 35 single word instructions) CMOS FLASH-based 8-bit microcontroller packs Microchip's powerful PIC® architecture into an 40- or 44-pin package and is upwards compatible with the PIC16C5X, PIC12CXXX and PIC16C7X devices. The PIC16F877A features 256 bytes of EEPROM data memory, self programming, an ICD, 2 Comparators, 8 channels of 10-bit Analog-to-Digital (A/D) converter, 2 capture/compare/PWM functions, the synchronous serial port can be configured as either 3-wire Serial Peripheral Interface (SPI™) or the 2-wire Inter-Integrated Circuit (I²C™) bus and a Universal Asynchronous Receiver Transmitter (USART). All of these features make it ideal for more advanced level A/D applications in automotive, industrial, appliances and consumer applications.

PIC16F72-I/SP MCP

  • This powerful (200 nanosecond instruction execution) yet easy-to-program (only 35 single word instructions) CMOS FLASH-based 8-bit microcontroller packs Microchip's powerful PIC® architecture into an 28-pin package and is upwards compatible with the PIC16C5X, PIC12CXXX and PIC16C7X devices. The PIC16F72 features 5 channels of 8-bit Analog-to-Digital (A/D) converter with 2 additional timers, capture/compare/PWM function and the synchronous serial port can be configured as either 3-wire Serial Peripheral Interface (SPI™) or the 2-wire Inter-Integrated Circuit (I²C™) bus. All of these features make it ideal for more advanced level A/D applications in automotive, industrial, appliances and consumer applications.

PIC16F688-I/SL MCP

  • The Low Pin-count (14) PIC® Flash microcontroller products offer all of the advantages of the well recognized mid-range x14 architecture with standardized features including a wide operating voltage of 2.0-5.5 volts, on-board EEPROM Data Memory, and nanoWatt Technology. Standard analog peripherals include up to 8 channels of 10-bit A/D, an analog comparator module w/ programmable on-chip voltage reference and an Enhanced USART (EUSART) peripheral that supports communications protocols such as RS232/485 as well as the LIN protocol.

PIC16F676-I/SL MCP

  • This powerful (200 nanosecond instruction execution) yet easy-to-program (only 35 single word instructions) CMOS Flash-based 8-bit microcontroller packs Microchip’s powerful PIC® MCU architecture into a 14-pin package and features 8 channels for the 10-bit Analog-to-Digital (A/D) converter, 1 comparator and 128 bytes of EEPROM data memory. This device is easily adapted for automotive, industrial, appliances and consumer entry-level product applications that require field re-programmability.

PIC16F628-I/SO MCP

  • PIC16F628-I/SO MCP

PIC16F628-I/SO MCP

  • This powerful (200 nanosecond instruction execution) yet easy-to-program (only 35 single word instructions) CMOS FLASH-based 8-bit microcontroller packs Microchip's powerful PIC® architecture into an 18-pin package and is upwards compatible with the PIC16F628, PIC16C62XA, PIC16C5X and PIC12CXXX devices. The PIC16F628A features 4MHz internal oscillator, 128 bytes of EEPROM data memory, a capture/compare/PWM, a USART, 2 Comparators and a programmable voltage reference that make it ideal for analog/integrated level applications in automotive, industrial, appliances and consumer applications.

PIC16F1939-I/PT MCP

  • This versatile 40-pin MCU is also a member of Microchip's extreme low power microcontroller family featuring nanoWatt XLP technology. Debug Support • Integrated debug support on Device. No Debug Header is required • An optional external Debug Header, AC244035 or AC244036, is also available for Debugging support • Debug and Programming support is available via PICkit™ 3, and MPLAB® ® ICD 3

PIC16F1823-I/SL MCP

  • IC MCU 8BIT 3.5KB FLASH 14SOIC

PIC16F1789-I/P MCP

  • Enhanced Mid-Range Core with 49 Instructions and 16 Stack Levels
  • Flash Program Memory with Self Read/Write Capability
  • 256 Bytes of EEPROM
  • Internal 32 MHz Oscillator
  • 4 x PSMC (Programmable Switch Mode Controller)
  • Dedicated 16-bit PWM with Digital and/or Analog Feedback Control
  • PWM Features: Dead-Band Control, Auto Shutdown & Restart
  • 4 x Fast Comparators with Selectable Voltage Reference
  • 3 x Operational Amplifiers (Rail-to-Rail Input and Output)
  • 14 x 12-bit ADC with Voltage Reference
  • 8-bit DAC
  • 3 x 5-bit DAC
  • MI2C / SPI / EUSART with Auto Baud Detection
  • 3 x Compare/Capture/PWM Modules
  • Two 8-bit Timers (TMR0, TMR2)

PIC16F1788-I/SP MCP

  • Part Number: PIC16F1788-I/SP
  • Core Size: 8-bit
  • Functionality: Microcontroller
  • Type: Leaded
  • Package: DIP
  • Number of Pins: 28
  • Brand: Microchip
  • Memory Size: 28 KB
  • Serial Port: Yes
  • Condition: New

PIC16F15355-I/SP MCP

  • PIC16F15355-I/SP MCP

PIC16F1512-I/SS MCP

  • PIC16F1512-I/SS MCP

PIC16F1508-I/P MCP

  • PIC16F1508-I/P MCP

PIC16F1503T-I/SL MCP

  • PIC16F1503T-I/SL MCP

PIC12F675T-I/SN MCP

  • PIC12F675T-I/SN MCP

PIC12F675-I/SN MCP

  • PIC12F675-I/SN MCP

PIC12F510-I/SN MCP

  • PIC12F510-I/SN MCP

PIC12F510-I/P MCP

  • PIC12F510-I/P MCP

PIC12F508-I/P MCP

  • Brand: Microchip
  • Package Type: 0.75 KB
  • Part Number: PIC12F508-I/P
  • Timers: 1 x 8-bit
  • Application: Electronics

PIC12F1501-I/SN MCP

  • Part Number: 20581MU
  • Model Number: PIC12F1501-I/SN
  • Pin Count: 8
  • Package Type: SOIC
  • Program Memory Size: 1.75 KB
  • Operating Voltage: 5 V
  • ADC Channels: 4
  • Max ADC Resolution: 10-bit
  • CPU Speed: 5 MIPS

PCF8583T NXP

  • PCF8583T NXP

DSPIC30F4011-30I/P MCP

  • Core Size: 32-bit
  • Device Core: 32-bit
  • Brand: Microchip
  • Part Number: DSPIC30F4011-30I/P
  • RAM Size: 512 Bytes (On-Chip Data RAM)
  • Package Type: DIP
  • Mounting Type: DIP
  • Minimum Order Quantity: 10 Pieces

AS5147-HTST AMS-OSRAM

  • AS5147-HTST AMS-OSRAM

ATTINY2313A-PU MCP

  • ATTINY2313A-PU MCP

ATTINY13A-PU MCP

  • ATTINY13A-PU MCP

ATMEGA8A-AU MCP

  • High-performance, Low-power Microchip AVR® 8-bit Microcontroller
  • Advanced RISC Architecture - 130 Powerful Instructions – Most Single-clock Cycle Execution - 32 x 8 General Purpose Working Registers - Fully Static Operation - Up to 16MIPS Throughput at 16MHz - On-chip 2-cycle Multiplier

ATMEGA328P-PU MCP

  • The high-performance Microchip picoPower 8-bit AVR® RISC-based microcontroller combines 32 KB ISP Flash memory with read-while-write capabilities, 1024B EEPROM, 2 KB SRAM, 23 general purpose I/O lines, 32 general purpose working registers, three flexible timer/counters with compare modes, internal and external interrupts, serial programmable USART, a byte-oriented Two-Wire serial interface, SPI serial port, a 6-channel 10-bit A/D converter (8-channels in TQFP and QFN/MLF packages), programmable watchdog timer with internal oscillator, and five software selectable power saving modes. The device operates between 1.8-5.5 volts. By executing powerful instructions in a single clock cycle, the device achieves throughputs approaching one MIPS per MHz, balancing power consumption and processing speed

ATMEGA328P-PU MCP

  • The high-performance Microchip picoPower 8-bit AVR® RISC-based microcontroller combines 32 KB ISP Flash memory with read-while-write capabilities, 1024B EEPROM, 2 KB SRAM, 23 general purpose I/O lines, 32 general purpose working registers, three flexible timer/counters with compare modes, internal and external interrupts, serial programmable USART, a byte-oriented Two-Wire serial interface, SPI serial port, a 6-channel 10-bit A/D converter (8-channels in TQFP and QFN/MLF packages), programmable watchdog timer with internal oscillator, and five software selectable power saving modes. The device operates between 1.8-5.5 volts. By executing powerful instructions in a single clock cycle, the device achieves throughputs approaching one MIPS per MHz, balancing power consumption and processing speed

ATMEGA16A-PU MCP

  • Brand: Atmel
  • Model Number: ATMEGA16A-PU
  • Mounting Type: Through Hole
  • Package Type: Tube
  • Number of Pins: 40
  • Input Type: DC
  • Operating Temperature: -40°C to 100°C
  • Minimum Order Quantity: 100 Pieces

ATMEGA16A-AU MCP

  • ATMEGA16A-AU MCP

ATMEGA128A-AU MCP

  • Features • High-performance, Low-power AVR® 8-bit Microcontroller • Advanced RISC Architecture – 133 Powerful Instructions – Most Single Clock Cycle Execution – 32 x 8 General Purpose Working Registers + Peripheral Control Registers – Fully Static Operation – Up to 16 MIPS Throughput at 16 MHz – On-chip 2-cycle Multiplier • High Endurance Non-volatile Memory segments – 128K Bytes of In-System Self-programmable Flash program memory – 4K Bytes EEPROM – 4K Bytes Internal SRAM – Write/Erase cycles: 10,000 Flash/100,000 EEPROM – Data retention: 20 years at 85°C/100 years at 25°C(1) – Optional Boot Code Section with Independent Lock Bits In-System Programming by On-chip Boot Program True Read-While-Write Operation – Up to 64K Bytes Optional External Memory Space – Programming Lock for Software Security – SPI Interface for In-System Programming

AT93C46B-10PC-2.7V ATMEL

  • AT93C46B-10PC-2.7V ATMEL

We are Stockist & Traders of Electric Components Active & Passive Components.

GET IN TOUCH

3A, 3RD FLOOR 399/399A, MANEK CHAMBERS DR. D.B MARG, MUMBAI - 400004
+91-9152743505
+91-9321743505
+91-8591743505
info@bitchipsemiconductors.com

FOLLOW US

Copyright © 2026 BITCHIP SEMICONDUCTOR. | Designing by TESRON WEBTECH.